Blog

Heating and Air Systems in Frisco, TX

Heating and Air Systems in Frisco, TX

If you don’t like cold showers then you must ensure the periodic inspection of your water heater systems. It is an inevitable task to keep them well maintained. When you ensure a detailed inspection of a water heater system, every six months time, you face fewer hot water problems. But for this, you must ensure this repair and inspection by employing the professional heating and air condition service in Frisco, TX.

 

Regular inspection reduces the likelihood of water heater breakdown. Not to mention, when your water heater stops working, it is a very distressing situation. You stop receiving the hot water and end up using cold water for dishwashingor even bathing. One more thing that might burn a hole in your pocket is the heavy replacement cost.

 

The need for the inspection of the water heater system is even more important when we talk about tanklesswater heaters as the professionals of heating and air condition service in Frisco, TX suggest. The same goes for solar units and even heat pumps. Tinkering with the efficient equipment is not at all a DIY job.

 

Handling a water heater job, without taking the assistance of a professional of heating and air condition service in Frisco, TX, is prohibited regardless ofwhich type of water heater you use. However, pay attention to the basic and most recommended maintenance steps to keep your water heater well functioning at all times.

 

If you have no idea what these steps are then read on. In this post,we will discuss some important ways to keep your water heater system well maintained. Remember all of these methods are highly recommended by the experts of heating and air condition service in Frisco, TX.

Look Around for Signs

There are some areas of your water heater that clearly indicate different warning signs. So it is very important to check all these areas before you touch the water heater or consider its replacement by employing the professionals of heating and air condition service in Frisco, TX. All of these problems indicate that the problem is imminent.

However, the foremost thing you need to inspect is the showers and faucets. You must check if the hot water has become hotter or colder. In case you find either of the situation to be true, this indicates a major problem with the heating element or thermostat as the experts of heating and air condition service in Frisco, TX suggest.

 

Check, Replace, Flush

This is another major step to ensure the regular inspection of the water heater system. This involves the followings;

Inspection of the main pressure relief valve

The pressure valve is an important component of a water heater system. It is responsible to easily take off the tank’s water pressure. If this valve is absent or stops working, the tank pressure may increase too much and it might lead to the point of tank explosion. Thus, to find this particular valve, look for the label as the water heater always comes with an attached label. But if you don’t find any label then you must check the product manual of the water heater system.

 

Needless to say, to be sure about everything and to perform the inspection properly, your best bet is to hire the professionals of a heating and air condition service in Frisco, TX.

 

Also to inspect the water heater valve, you can also open it manually to ensure its smooth working. But even before this, you must remain sure that the drain outlet is clear. When a valve is working properly, hot water easily sprays out.

 

Flushing the tank of your water heater

You can also start the inspection by flipping the circuit breaker or by shutting off the main inlet valve of cold water. Next is to connect the hose to the main drain outlet. Simply run the drain outlet either outside or down the drain of the floor. Now open the pressure relief valve to empty the tank and drain it quickly.

 

This particular step is crucial to remove the sediment. This accumulated sediment not only harm the water heater tank but it also needsyou to spend a good amount of money in terms of replacement and by hiring the professionals of a heating and air condition service in Frisco, TX.

 

As soon the tank is fully drained, shut off the drain valve and pressure relief. Now you should turn on each hot water faucet in your home and check if all the faucets are dry. Next is to open the cold water inlet and simply fill the tank. When the water starts running, flip your circuit breaker and let the water heater to start heating the clean and sediment-free tank.

 

Inspection of the anode rod

The anode rod is more of a long metal rod that usually extends up to the main water tank. This rod helps in accumulating and attracting the corrosive element.  This means that your tank remains free from rusting or even producing rusty water.

 

But the same process causes this rod to get rusted. Not to mention when the anode rod is completely consumed, it is your water heater tank’s turn to get rusted.  The rust damage gets transferred to the tank which is why periodic inspection of the anode rod is crucial by hiring the heating and air condition service in Frisco, TX.

 

In the bottom line

If you don’t inspect your water heater, every so often, or if you fail to uphold it, start this practice from today. However, if the damage has already been done or if it’s too late, employ the professionals for the replacement of the water heater. Call only the skilled and well-reputed service in such as K&S Heating and Air.

 

Their team of experts is well-versed in handling the multifaceted water heater issues. You can contact them anytime by calling their customer helpline number available on their official website.